多功能刷種機作原理：

物料進入刷種筒內，在彈性尼龍的推動作用下，使種子與脫絨筒壁、種子與種子之間相互磨檫去除表面的絨毛。脫下的絨毛被風機吸走，進入除塵器，沉降后定期排放。達到初部清選的目的。物料依次通過三個刷種筒后，好種子從第三筒排出，進入下一道清選工序。

主要適用于無殼南瓜籽的脫絨，脫絨后種子表面光滑，流動性好，易于清選。包衣時種衣劑的表面附著力強，包衣效果好。

多功能刷種機調整

(1）電機軸與主軸之間皮帶張緊度的調節

當皮帶張緊度需要調節時，首先松開電機與電機座的四個螺栓，順著電機座上的長孔移動電機，使皮帶張緊適當，然后擰緊螺栓。

(2>刷種間隙和刷種時間的調節

種子開始加工時，從出料口觀察刷種情況，若有種子破碎現象，則應增大刷種間隙;若刷種不*時，則應減小刷種間隙;若刷種效果好時，則將出料口擋板降低，使種子在刷種筒內停留時間（即刷種時間)縮短，增加生產率。

注意:此調整均應停機進行。

(3）主軸轉速的調節

通過更換電機皮帶輪或調節電流頻率來實現。轉速越高，刷種效果越明顯，反之亦然。更換皮帶輪后，皮帶的張緊度要作相應的調整。

調整毛刷與篩筒筒壁之間的間隙、改變主軸轉速或控制排料時間等均可改變刷種強度，以適應不同種子的表面處理，但刷種強度不宜過高，以免使種子表皮產生損傷或種溫增加過多，降低種子的發芽率。